SN-V4 Pro - Introduction

Before use, charge the saber fully with the provided cable and charging block, or external charger. Make sure to not supply more than 5V and 1A output to the saber or charge the saber while it's on. If those numbers mean gibberish then don't worry, that's what the charging block is for!

Charge for about 3 hours for but make sure not to leave it completely unattended.

To insert the blade, use the provided hex key to loosen the emitter blade retention screws. Insert the blade and tighten the screws just enough to hold the blade in place with friction.

Be careful not to over-tighten, as this will dent and damage the blade. Light marks on the blade from the set screw is expected.

Features

SN-Pixel V4 comes with a large library of sound fonts (27) already on the SD card but you can add even more just by dragging and dropping it on the SD card. There are at least 10 blade styles and 12 preon effects that can be configured with even more available to be customized via the mobile app!

Sound Fonts

Default Sound Fonts

Here are the 27 default sound fonts included on the SD card. You may add, edit, or delete sound fonts but make sure you keep a backup of the files on your local hard drive.

 

Number Sound Font Name Sound Font Artist
1 Ani's Padawan JuanSith
2 Angry Ani JuanSith
3 Blue Lady Master JuanSith
4 Master Depa JuanSith
5 D-Maul JayDalorian
6 Dookula JuanSith
7 Dark Sith Red Mountain Sabers
8 Emperor kyberphonic
9 Fallen Order Cal JuanSith
10 Frolic Frog JuanSith
11 Graflex IX JuanSith
12 Grumpy Ben JuanSith
13 Inquisitor JuanSith
14 L-Skywalker JayDalorian
15 Mace Windy JuanSith
16 Mando Saber JuanSith
17 Master Mundi JuanSith
18 Obi Ep III JuanSith
19 Quin Vos JuanSith
20 Revanchist - Reborn JuanSith
21 Revanchist - The Butcher JuanSith
22 Temple Guard JuanSith
23 TFU 2 Secret Apprentice JuanSith

24

 The Lost Sister JuanSith

25

 The Princess JuanSith
26 Tulak: The Greatest Swordsman JuanSith
27 Rogue Vader JuanSith

SN-V4 Pro Button Operations

Two Button Operation

Hibernate
Wake up saber Hold the Main button
Switch between blade lengths for 32" and 36" blades Quickly tap the Main button 3 times

 

Standby
Ignite saber Tap button

or

Twist the saber
Adjust volume Hold the Main and Aux button at the same time, release after the loud beep prompt to enter volume change mode.
Click Main button to increase the volume and click Aux button to decrease the volume.
Press and hold Main and Aux button to exit
Switch preon effect

Hold the Main button for 1s
Switch blade style Hold the Aux button for 1s
Switch sound fonts Tap the Aux button

or

With the saber pointed up, hold the Aux button and twist the saber
Switch background music With the saber pointed down, hold the Aux button and twist the saber
Enter hibernate mode Tap the Aux button 3 times

or

Automatically enters hibernate mode after idling for 10 minutes

 

Ignited
Blaster block Tap the Aux button
Flash on Clash Hard clash on the saber
Lockup Hold the Aux button for 1s. Tap either button again to disengage lockup
Colour change With the saber pointed down, hold the Aux button and twist the saber
Retract saber Tap the Main button

or

Twist the saber
Force effect With the saber pointed up, hold the Aux button and twist the saber
Drag effect Hold the Main button and clash the blade. Tap either button again to disengage drag effect.
Melt effect Thrust the saber horizontally forward
Enable or Disable Flash on Clash Hold the Main and Aux button at the same time then release

One Button Operation


Hibernate
Wake up saber Hold button
Switch between blade lengths for 32" and 36" blades Quickly tap the button 3 times

 

Standby
Ignite saber Tap button

or

Twist the saber
Adjust volume Hold the button for 1s or 1 LED button blink
Switch preon effect

Hold the button for 2s or 2 LED button blinks
Switch blade style Hold the button for 3s or 3 LED button blinks
Switch sound fonts Hold the button for 4s or 4 LED button blinks

or

With the saber pointed up, hold the button and twist the saber
Switch background music With the saber pointed down, hold the button and twist the saber
Enter hibernate mode Hold the button for 5s or 5 LED button blinks
Automatically enters hibernate mode after idling for 10 minutes

 

Ignited
Blaster block Tap the button
Flash on Clash Hard clash on the saber
Lockup Hold the button for 1s or 1 LED button blink. Tap the button again to disengage lockup
Colour change Hold the button for 2s or 2 LED button blinks
With the saber pointed down, hold the button and twist the saber

The saber will cycle through the colours, tap the button again to select it
Enable or Disable Flash on Clash Hold the button for 3s or 3 LED button blinks
Retract saber Hold the button for 4s or 4 LED button blinks
Twist the saber
Force effect With the saber pointed up, hold the button and twist the saber
Drag effect Hold the button and clash the blade
Melt effect Hold the button and thrust the saber horizontally forward

SN-V4 Pro - ForcePark V2

SN-V4 Pro can be paired with a mobile app on Android on iOS called "ForcePark V2". This app allows you to operate your saber remotely and edit blade style settings.

The app "ForcePark V2" is currently available on iOS on the App Store and on the Google Play Store (once available)

It currently has the below icon:

You can find a guide on how to navigate the app below:
ForcePark V2 App Operation Guide


June 2024
For Android users "ForcePark V2" is currently not public on the Google Play Store yet. You can download the app via the link below:
https://www.saberopen.com/download/forceparkv2.apk

SN-V4 Pro - Firmware Updates

To manually update the saber's firmware you can follow the steps below as well as download the appropriate firmware update file.


To update the firmware of your soundboard:

  1. Remove the core from the saber
  2. Remove the battery from the core
  3. Remove the SD card from core
  4. Insert the SD card into your PC with a micro SD card reader
  5. Download the appropriate firmware binary
  6. Copy the binary to the root of the SD card
  7. Re-insert the SD card back into the soundboard
  8. Re-insert the battery back into the core
  9. Wait for the saber to finish updating
Firmware Updates

September 2024

SN-V4 Pro - More Information

Battery Removal and Insertion

Some sabers may use an external battery charger which require removing the battery to recharge it. You may also want to remove the battery to reseat it in your ECO Saber or charge it externally. Below is a demo showing how to remove the battery from the tight battery holder and re-inserting it back in the core.

Saber with multiple blade retention screws

What if my saber has multiple blade retention screws? Should I tighten them all in?

Good question, here are some diagrams to illustrate which ones you should tighten. The blade retention screws are marked in blue and the contact points acting on the blade are marked in red.


In the middle diagram with all retention screws tightened, the red areas marked in red are the surface area contact points of the blade. Note how it's only really making contact with the 4 retention screws and the opposite ones are counteracting against each other.

Whereas in the 3rd diagram on the right, where only retention screws on the same side are tightened, the blade has much more surface area contact with the inside wall of the hilt itself.

It's preferred to tighten retention screws on the same side, or 90 degrees from each other so the blade has more surface contact which results in it being held in the saber tighter.